|
| 外型尺寸 | |
| 貨號 | KS8591679 |
| 品牌 | KAYSEN |
| 用途 | 抽水、化工、制藥、石油、冶金、染料、冶煉、電力、電鍍、農藥、造紙、食品、紡織等行業酸洗工藝、制酸制堿、噴漆工藝、有色金屬冶煉中的電解液輸送、離子膜項目中的氯水輸送、廢水處理、電鍍、農藥領域。 |
| 型號 | KAYSEN |
| 工作壓差 | 0 |
| 壓力環境 | 常壓 |
| 介質溫度 | 250℃ |
| 驅動方式 | 電動 |
| 適用介質 | 水 |
旋渦泵-不銹鋼旋渦泵-KAYSEN泵業
GERMANY KAYSEN PUMP CO .,LTD
旋渦泵是指葉輪為外緣部分帶有許多小葉片的整體*，液體在葉片和泵體流道中反復做旋渦運動的泵。旋渦泵雖屬于葉片式機械的范疇，但其工作過程、結構以及特性曲線的形狀等與離心泵和其他類型泵都不太相同。
主要特點：
●旋渦泵是結構最簡單的高揚程泵。與相同尺寸的離心泵相比，它的揚程比離心泵高2～4倍；與相同揚程的容積泵相比，它的尺寸要小得多，結構也簡單得多。
●旋渦泵的效率很低（由于液體在流道內撞擊損失較大），*不超過45%，通常為15%～40%。因此，它難做成大功率的泵。從如今生產的旋渦泵來看，功率一般不超過30 kw。但低比轉數的離心泵效率比它還低，因此，旋渦泵代替低比轉數的離心泵使用的場合是很多的。
●大多數旋渦泵都具有自吸能力，有些旋渦泵還可以抽氣或抽送汽液混合物，這是一般離心泵無能為力的。
具體來說，對于閉式葉輪旋渦泵，只要設置一個簡單的附加裝置即可以自吸。對于開式葉輪、閉式流道的旋渦泵來說，它具有自吸能力，通常用于抽氣；而開式葉輪、開式流道的旋渦泵則用作輸送液體，不能自吸。通常這兩種泵組裝在一起，前者作為抽真空泵，后者作為工作泵。例如，加油車的旋渦泵，還有其他結構的旋渦泵。
主要應用：
●在化學工業中輸送酸、堿及其他腐蝕性液體，要求泵具有小流量、高揚程、較慢的化學反應速度和較高的耐腐蝕性。由于旋渦泵的工作零件簡單，因此易于實現上述要求。
●抽送介質密度小的液體（如汽油、酒精等）。由于這些液體易于揮發，因此抽送時多為汽液混輸，如機場、汽車配油站，甚至于飛機的加油。旋渦泵能進行汽液混輸，在上述情況下工作，一般時間短，所以，效率低就不是主要問題了。
●抽送含有氣體的液體，抽送含有高彈性氣體的液體（如丙烷、丁烷等）。抽送吸入管中部分蒸發的液體。
●用于小型自動化泵站，農業供水。
●用于城市公用建設，如增壓輔助泵、家庭用水等。
●代替液環泵作真率泵和低壓壓縮機。
●用于汽出及船用洗滌、飲水、消防等輔助設備。
●用于小型鍋爐輔助設備，用以供水。
旋渦泵常見故障排除法：
1、故障：旋渦泵消耗功率過大
解決辦法：放松填料壓蓋，更換葉輪。關小閘閥，減小流量。
2、故障：旋渦泵不吸水，壓力表劇烈跳動
解決辦法：灌足引水，檢查管路，排除漏氣現象。
3、故障：出口壓力表指示有壓力，泵出水很少或不出水解決辦法:降低管阻。
解決辦法：檢查電機轉向，除去葉輪堵塞物。增加轉速。
4、故障：漩渦泵流量低于設計流量
解決辦法：除去堵塞物，更換密封環，增加轉速至銘牌上的規定值。
5、故障：旋渦泵內聲音反常，泵不出水
解決辦法：檢查吸水管有無堵，清理底閥，降低液體溫度或降低吸水高度。
6、故障：旋渦泵噪聲大
解決辦法：調整旋渦泵和電機，保證同心，更換新軸承。
7、故障：旋渦泵軸承發熱
解決辦法：加油，換好油或粘度小的油。更換軸承。調整泵和電機，保證同心。
8、故障：真空表指示高度真空，泵仍不吸水。
解決辦法：檢查底閥活門靈活性，除掉堵塞物，盡量使吸水管路簡單。降低吸水高度。
9、故障：水泵振動
解決辦法：調整泵和電機使軸線對準，葉輪通過平衡試驗，不平衡重量要求在3克左右，更換軸承。
不管任何的設備機械，在使用上或多或少都會遇到一些故障或者問題，只要在故障出現時，及時的解決，還是可以保證正常工作的。所以，要重視平時的操作方法與保養維護，是保證旋渦泵運行的關鍵。
Vortex pump
Vane pump
The vortex pump refers to a pump in which the impeller is an integral wheel with many small blades on the outer edge portion, and the liquid repeatedly performs a vortex motion in the blade and the pump body flow passage. Although the vortex pump belongs to the category of vane machinery, its working process, structure and shape of the characteristic curve are not the same as those of centrifugal pumps and other types of pumps.
main feature:
●The vortex pump is the simplest high-lift pump. Compared to a centrifugal pump of the same size, its lift is 2 to 4 times higher than that of a centrifugal pump; it is much smaller and simpler in construction than a positive displacement pump.
●The efficiency of the vortex pump is very low (due to the large impact loss of the liquid in the flow channel), the maximum is no more than 45%, usually 15% to 40%. Therefore, it is difficult to make a high-power pump. From the perspective of vortex pumps produced today, the power generally does not exceed 30 kw. However, the efficiency of a centrifugal pump with a low specific speed is lower than that of a centrifugal pump, and therefore, the vortex pump is used in place of a low specific speed centrifugal pump.
● Most vortex pumps have self-priming capability. Some vortex pumps can also pump or pump vapor-liquid mixture, which is a powerless pump.
Specifically, for a closed impeller vortex pump, it is self-priming as long as a simple attachment is provided. For open-type impellers, closed-flow vortex pumps, it has self-priming capability and is usually used for pumping; while open-type impellers and open-flow vortex pumps are used to transport liquids and cannot self-prime. Usually these two pumps are assembled together, the former as a vacuum pump and the latter as a working pump. For example, the vortex pump of a fuel truck has other vortex pumps.
main application:
● The transport of acids, bases and other corrosive liquids in the chemical industry requires pumps with low flow rates, high lifts, slow chemical reaction rates and high corrosion resistance. Since the working parts of the vortex pump are simple, it is easy to achieve the above requirements.
● Pumping liquids with low media density (such as gasoline, alcohol, etc.). Because these liquids are easy to volatilize, they are often mixed with vapor and liquid during pumping, such as airports, car distribution stations, and even aircraft refueling. The vortex pump can perform vapor-liquid mixing and work under the above conditions, and the general time is short. Therefore, low efficiency is not a major problem.
● Pumping a liquid containing a gas and pumping a liquid containing a highly elastic gas (such as propane, butane, etc.). The partially evaporated liquid in the suction tube is pumped.
●Used for small automated pumping stations and agricultural water supply.
●Used for urban public construction, such as booster auxiliary pumps, household water, etc.
● Replace the liquid ring pump as a true rate pump and a low pressure compressor.
●Used for auxiliary equipment such as steaming and marine washing, drinking water and fire fighting.
●Used for small boiler auxiliary equipment for water supply.
Vortex pump common troubleshooting method:
1, fault: vortex pump consumes too much power
Solution: Loosen the packing gland and replace the impeller. Close the small gate valve to reduce the flow.
2, failure: the vortex pump does not absorb water, the pressure gauge beats vigorously
Solution: Fill the water, check the pipeline, and eliminate the air leakage.
3. Fault: The outlet pressure gauge indicates that there is pressure, and the pump has little or no water. Solution: Reduce the pipe resistance.
Solution: Check the motor steering to remove the impeller blockage. Increase the speed.
4. Fault: vortex pump flow is lower than design flow
Solution: Remove the blockage, replace the seal ring, and increase the speed to the specified value on the nameplate.
5, fault: the sound in the vortex pump is abnormal, the pump does not produce water
Solution: Check the suction pipe for blockage, clean the bottom valve, lower the liquid temperature or lower the water absorption height.
6, fault: vortex pump noise
Solution: Adjust the vortex pump and motor to ensure concentricity and replace the new bearing.
7, fault: vortex pump bearing heat
Solution: Refuel, change oil or oil with low viscosity. Replace the bearing. Adjust the pump and motor to ensure concentricity.
8. Fault: The vacuum gauge indicates a high vacuum and the pump still does not absorb water.
Solution: Check the flexibility of the bottom valve to remove the blockage and try to make the suction pipe as simple as possible. Reduce the water absorption height.
9, fault: pump vibration
Solution: Adjust the pump and motor to align the axis. The impeller passes the balance test. The unbalanced weight requirement is about 3 grams, and the bearing is replaced.
Regardless of any equipment machinery, there will be some faults or problems in use, as long as the fault occurs, and timely solution can still ensure normal operation. Therefore, it is the key to ensure the operation of the vortex pump to pay attention to the usual operation methods and maintenance.
位于Schw?bischGmünd的凱森Kaysen泵業有限公司是世界*的各種流體水泵和隔膜泵制造商之一。60多年來，凱森以“制造”的可靠性和質量達到了*標準。憑借我們全面的產品組合，我們支持世界各地的客戶成功掌握供水，采礦，工業，化工，造紙，電力，食品，制藥，污水和海上行業的苛刻抽水任務。作為上述領域創新技術的*供應商，我們是液體需要安全，高效和經濟運輸的*合作伙伴。
凱森始終堅持“重質量，講信譽”為宗旨。產品現暢銷全國各地，并已逐步開發海外市場。公司多次被評為“重合同講信用”企業，深得用戶的信賴和廣泛的贊譽。
The Kaysen Pumps GmbH in Schw?bischGmünd, Germany, is one of the world's leading manufacturers of fluid centrifugal pumps and diaphragm pumps. For more than 60 years, Kaisen has achieved the highest standards of reliability and quality of "Made in Germany". With our comprehensive product portfolio, we support customers around the world to successfully grasp the harsh pumping tasks of water supply, mining, industry, chemical, paper, electricity, food, pharmaceutical, sewage and marine industries. As a leading provider of innovative technology in these areas, we are the perfect partner for liquids to be safe, efficient and economical to transport. ,
Germany Kaysen always adhere to the "quality, stresses credibility" for the purpose. Products are selling all over the country, and has gradually developed overseas markets. The company has repeatedly been rated as "the contract with the letter" business, won the trust of users and extensive praise.
